Відео

Awesome video!!

You put the outer seal in backwards

❤

Is it cheaper to make than to buy the crawler harness

I was unable to get the cap to break loose with my cheap spanner wrench, I tried a punch and hammer that didn't work either. I eventually heated the outside at the top to get it to break loose. I did not heat it enough to destroy the paint.

That bottom right plug is a check valve if you ever remove it you could loose the tiny spring and inside part of the check valve and they are no longer available. There is also a check valve on the back side of the unit exactly the same as the front one, one is for up the other is for down. I was able to find a balance point on the motor with the safety stand flipped down and was able to remove the top pin with a pair of pliers after I pulled out the split key. I used penetrating oil overnight and the bottom tapped out with no problem. Great video, was a great help to me.

Nice vid! I still have my Cyclops hair jigs

Hi, subscribed! I have emailed you requesting your file. I was wondering how you’ve concluded that the rail is strong enough for the weight of the motor and force of the thrust? Any insights on how you got comfort there? Are these mount configurations universal or do you need a different configuration depending on the motor?

Once i see piles of boats i tend to stay away from them less pressured

Amazing project. How long is your trolling motor's shaft?

Don't need all the musical noise, could use some comments during install instead.

When it shows the table full of fish at the end, look on the left end. It looks like they kept a bunch of white perch.

we have never jigged on Erie before. Only on the river. On our bucket listed

What size spanner wrench do I need ? Where can I purchase it ? I saw some on Amazon but wasn’t sure what size ? Any recommendations on the correct one ?

A very elegant solution! Do you think it might work with an 18’ Dauntless + 80lb thrust tm? Would you be so kind as to share your CAD file?

Great Video with the family and Mini fishing tool lol

Phenomenal, great job Andy

Very nice!....What trolling motor model is that?...54" shaft im guessing. battery location?...i have so many questions, I need to do this. thanks so much!

Electric knife works wonders been using one back when they came out in the late 60s fast and sharp

I have taken five over 5.5 pounds in the last eight days here in Southwest Oklahoma…

that's the fun way to catch walleye

I’m ready to get out on the ice now!

I have a 1997, 40 horse power Johnson, and mine is leaking at the top of the cap just like yours is but think my fluid is out cause it want move to much but you can hear the electrical part working so I am gonna do exactly the same way your replaced yours without removing the upper or lower pin. Seems alot quicker to me to do it exactly the way you did your reseal.

Is there a c clip that I missed ? And I got the upgrade kit and the three washers are missing

Hi. Can I buy one of those mounts from you? I need one for a 2020 Boston whaler 170 Montauk

Hey mate good day. I've got the same problem with my Johson 70hp. I can't pull it out the same pin that you showed. Is it possible to do this way in all Johnson outboard motor? Thanks so much.

Maybe I just missed it but what weight are the hair jigs?

what model rod and reel do you like to use?

What scissors are those?

Looks like you came out of gem Beach chanel where are you docked at?

What kind of rig setup are you using? Thanks

Awesome trip Clouse! You guys whacked’em again! Love these vids! Appreciate you showing folks how our High Dollar Hair Jigs get the job done on those walleye 🎣🔨🔥🐍🙌

I love lake Erie I love Fremont I love mommy for the White Bass run crappie and bluegill smallmouth bass largemouth bass Hoover dam Allen Creek deer Creek griggs dam good fishing dealers dam 36 37 good fishing there too

Thx again for ur help. I switched out the old power and it fired right up

Hi was wondering if you can help me out. I have the same motor as u and my motor is not get spark. Do you think it can be the power pack?

Looks like TM mount held up. Any feedback on design and suggestions after years of use?

Thanks for the video, very helpful. Quick question, did you release the manual release before you lift the ram up and remove it?

Best music yet! Wish my Fury 16 Tiller would work there...

Thanks for this. Like mine, I notice when you are filling it with new oil, the unit is not exactly level as it is slightly at an angle with the transom. Does this matter as far as filling it with oil and getting as much as possible in there? I've tried to find a hill steep enough to get mine level when I'm filling it but haven't found one yet. I'm putting off changing these seals but I'm researching and buying the tools needed as I know it will need to be done at some point as it leaks at the top of the piston and the motor slowly seeps down. But for now it works enough to keep fishing.

Any advice for ice fishing?

Think it was great you released those critters. I know you keep some to eat, I do to. There are tons of people that fish there that keep everything, I've seen them , no ODNR people ever get out of truck to ever check size or amount... Ever! That's my home lake and it's a shame. Videos are great, keep them coming. Fish on brother.

Nice looking dinner.

I was fishing for saugeye at leibs island in the channel where the stream comes in. Just got a new st. Croix rod. Was there 10 minutes and already caught 2 small saugeye. Hooked into another small one and was almost to the bank when a pike grabbed it . I was so surprised at the sight of it ,I jerked my rod so hard it broke in half and I lost both fish. The damm pike was only maybe 2 foot long.... that sucked but I know what I saw. It was definitely a pike.

Fish tacos and football games! Great day.. Nice catch sir. Hopefully brother and myself are gonna be there later this afternoon.

Oh yea, we need more videos!

One of your best video's so far. Everything you were saying and going through was spot on.. Tight lines to you brother and Happy Thanksgiving to you and yours.

We need to talk I'm always fishing there hope I run into you one day

Youre a legend. i was just gonna put a plate(and not as robust of one) across the corner of my rail and u bolt it but you have built a masterpiece

Thank you for the informative video. I just used your idea on my year 2002 Johnson 40hp and it worked great !

Love the colors on the firetiger gotta be one of my fav lures. Looks like you found a nice jig head to match. Couple questions. What jighead and where to you buy your lures/jigs